Max RB397 Spezifikationen

RB397(USA)OPERATING and MAINTENANCE MANUALMANUEL D'OPERATION ET D'ENTRETIENMANUAL DE OPERACIÓN Y MANTENIMIENTORE-BAR TYING TOOLOUTIL POUR LI

11<Battery pack>3. WIRE SPECIFICATIONSBATTERY CHARGER:Use only an authorized Battery charger, MAX JC928.4. TECHNICAL DATA1 NOISEA-weighted singl

12This equipment has been verified to comply with the limits for a Class B personal digital device, pursuant to Subpart B of Part 15 of FCC Rules. Onl

134. BATTERY INSTRUCTIONS1. Charging• Before removing the Battery pack from the tool, set the Main switch at OFF and lock the Trigger.1 A Pack cap tha

14When the Battery pack is at low tem-peratureWhen the Battery pack is at low temperature, its charging is automatically suspended until its tem-perat

15(1) After you have recharged the battery pack, remove it from the charger.(2) Unplug the charger power cord from the wall socket.Regarding tying tim

16Indication of Quick Charger Lamps∗ For batteries those are at low temperatures (50°F (10°C) or lower), charging time must be extended longer.Charger

17Service Life of the Battery PackIf any condition described below is observed, the battery pack is at the end of its service life. Re-place it with a

182 Peel off the tape fixing Tie-Wire by about 2" (5cm). Stretch out the tip of the wound Tie-Wire.BE SURE TO USE ONLY THE SPECIFIED TIE-WIRE (MA

19If the window is dirty and the pipe po-sition can not be confirmedOpen the window and wipe off the dirt on the in-side of the window with a soft clo

200 Unlock the Trigger before using the tool.2. How to remove the Tie-Wire• Be sure to turn the Main switch OFF, lock the Trigger, and remove the Batt

3INDEX1. SAFETY INSTRUCTIONS...32. SAFETY FEATURES...

213 Slide the Reel stopper to release the Reel holder and remove the Tie-Wire.4 Mount the new Tie-Wire. (Refer to the Tie-Wire mounting method explana

222 This dial allows you to adjust wire tension torque slightly.To increase the tension, turn it in the coun-terclockwise.To decrease the tension, tur

235. For proper tightness1 Tilt the tool 45° angle to the crossed re-bars.2 Apply the tool perpendicularly to the surface of the crossed re-bars.Durin

246. MAINTENANCE1 Regularly inspect the toolIn order to maintain the performance of the tool, periodically clean up and inspect the tool.2 Do not lubr

253. Remove the cutter and the fixed cutter, and clean them. (The removable parts are the cutter, fixed cutter, wire guide A and cutter plate unit.)As

267. Make sure that arm B is securely assem-bled and tighten the 2 (plated) hexagon socket head bolts M3 × 6. (Tightening torque: 15.2lbF·inch (172cN

279. TROUBLE SHOOTING/REPAIRSThe troubleshooting and/or repairs shall be carried out only by the MAX CO., LTD. authorized distribu-tors or by other sp

283. Trigger ON → Wire sent out.Sending of wire is stopped half-way.Four short beeps repeat-ed(Pipipipi, pipipipi, ...)Tie-Wire is not set in the too

41. WEAR SAFETY GLASSES OR GOGGLESThe employer and the user must make sure that proper eye protection is worn when the tool is being used. Eye protect

58. KEEP FINGERS AND BODY PARTS AWAY FROM THE TIE-WIRE REEL WHEN TOOL IS IN OPERATIONFailure to do so may result in serious injury.9. DO NOT POINT THE

615. USE ONLY THE AUTHORIZED BATTERY PACKUse only MAX JPL914 battery pack. If the tool is connected to a power supply other than the authorized pack,

76 Do not touch the power cord or plug with a wet hand or gloveThis may cause injury from electric shock.7 Do not put a cloth or any other cover on th

816This charger is not intended for use by children or disabled persons without supervisor.17Children should be supervised to en-sure that they do not

9Curl GuideWhen the Curl Guide is opened, it will emit a beeping sound and the tool does not operate.Curl Guide

103. SPECIFICATIONS AND TECHNICAL DATA1. NAME OF PARTS2. TOOL SPECIFICATIONSPRODUCT NO. RB397<Battery charger>WEIGHT 5.3lbs(Battery included) Pr